this is information on a product in full production. april 2012 doc id 8613 rev 5 1/9 9 stps41h100c low drop power schottky rectifier datasheet ? production data features negligible switching losses low leakage current good trade off between leakage current and forward voltage drop low thermal resistance avalanche capability specified description dual center tab schottky re ctifier suited for switch mode power supply and high frequency dc to dc converters. packaged in d 2 pa k , i 2 pak and to-220ab, this device is intended for use in high frequency inverters. j table 1. device summary symbol value i f(av) 2 x 20 a v rrm 100 v t j (max) 175 c v f (max) 0.67 v a1 k a2 a1 k a 2 a1 k a2 k a1 a2 to-220ab stps41h100ct d 2 pak stps41h100cg i 2 pak stps41h100cr www.st.com
characteristics stps41h100c 2/9 doc id 8613 rev 5 1 characteristics when the diodes 1 and 2 are used simultaneously: tj(diode 1) = p(diode1) x r th(j-c) (per diode) + p(diode 2) x r th(c) to evaluate the conduction losses use the following equation: p = 0.58 x i f(av) + 0.0045 i f 2 (rms) table 2. absolute ratings (limiting values, per diode) symbol parameter value unit v rrm repetitive peak reverse voltage 100 v i f(rms) forward rms current 30 a i f(av) average forward current t c = 50 c = 0.5 per diode per device 20 a 40 i fsm surge non repetitive forward current t p = 10 ms sinusoidal 220 a i rrm repetitive peak reverse current t p = 2 s square f= 1 khz 1 a p arm repetitive peak avalanche power t p = 1 s t j = 25 c 18100 w t stg storage temperature range -65 to + 175 c t j maximum operating junction temperature (1) 1. condition to avoid thermal runaway for a diode on its own heatsink 175 c dv/dt critical rate of rise of reverse voltage 10000 v/s table 3. thermal resistance symbol parameter value unit r th(j-c) junction to case per diode 1.5 c/w to t a l 0 . 8 r th(c) coupling 0.1 table 4. static electrical characteristics (per diode) symbol parameter test conditions min. typ. max. unit i r (1) 1. pulse test: t p = 380 s, < 2% reverse leakage current t j = 25 c v r = v rrm 10 a t j = 125 c 3 10 ma v f (1) forward voltage drop t j = 25 c i f = 20 a 0.80 v t j = 125 c i f = 20 a 0.62 0.67 t j = 25 c i f = 40 a 0.90 t j = 125 c i f = 40 a 0.70 0.76 dptot dtj < 1 rth(j-a)
stps41h100c characteristics doc id 8613 rev 5 3/9 figure 1. conduction losses versus average current figure 2. average forward current versus ambient temperature ( = 0.5) 0 2 4 6 8 10 12 14 16 0 5 10 15 20 25 if(av)(a) = 0.05 = 0.1 = 0.2 = 0.5 = 1 pf(av)(w) t =tp/t tp 0 2 4 6 8 10 12 14 16 18 20 22 0 25 50 75 100 125 150 175 tamb(c) rth(j-a)=rth(j-c) rth(j-a)=50c/w if(av)(a) t =tp/t tp figure 3. normalized avalanche power derating versus pulse duration figure 4. normalized avalanche power derating versus junction temperature 0.001 0.01 0.1 0.01 1 0.1 10 100 1000 1 t (s) p p(t) p (1s) arm p arm 0 0.2 0.4 0.6 0.8 1 1.2 25 50 75 100 125 150 t (c) j p) p (25c) arm (tj arm figure 5. non repetitive surge peak forward current versus overload duration (maximum values) figure 6. relative variation of thermal impedance junction to case versus pulse duration 0 50 100 150 200 250 300 1.e-03 1.e-02 1.e-01 1.e+00 t(s) tc=25c tc=75c tc=125c im(a) i m t =0.5 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.e-03 1.e-02 1.e-01 1.e+00 tp(s) = 0.5 = 0.2 = 0.1 single pulse zth(j-c)/rth(j-c) t =tp/t tp
characteristics stps41h100c 4/9 doc id 8613 rev 5 figure 7. reverse leakage current versus reverse voltage applied (typical values) figure 8. junction capacitance versus reverse voltage applied (typical values) 1.e-04 1.e-03 1.e-02 1.e-01 1.e+00 1.e+01 1.e+02 0 102030405060708090100 vr(v) tj=150c tj=125c tj=25c tj=100c tj=75c tj=50c ir(ma) 0.1 1.0 10.0 1 10 100 vr(v) f=1mhz vosc=30mv tj=25c c(nf) figure 9. forward voltage drop versus forward current figure 10. thermal resistance junction to ambient versus copper surface under tab 1 10 100 0.0 0.2 0.4 0.6 0.8 1.0 1.2 vfm(v) tj=25c (maximum values) tj=125c (maximum values) tj=125c (maximum values) tj=125c (typical values) tj=125c (typical values) ifm(a) 0 10 20 30 40 50 60 70 80 0 5 10 15 20 25 30 35 40 s(cm2) rth(j-a)(c/w) (epoxy printed board fr4, cu = 35 m) - stps41h100cg only
stps41h100c package information doc id 8613 rev 5 5/9 2 package information epoxy meets ul94, v0 recommended torque values for to-220ab: 0.4 to 0.6 nm in order to meet environmental requirements, st offers these devices in different grades of ecopack ? packages, depending on their level of environmental compliance. ecopack ? specifications, grade definitions and product status are available at: www.st.com . ecopack ? is an st trademark. devices in i 2 pak with nickel-plated back frame must not be mounted by frame soldering like smds. such devices are intended to be through-hole mounted only and in no circumstances shall st be held liable for any lack of performance or damage arising out of soldering of nickel-plated back frames. table 5. i 2 pak dimensions ref. dimensions millimeters inches min. max. min. max. a 4.40 4.60 0.173 0.181 a1 2.40 2.72 0.094 0.107 b 0.61 0.88 0.024 0.035 b1 1.14 1.70 0.044 0.067 c 0.49 0.70 0.019 0.028 c2 1.23 1.32 0.048 0.052 d 8.95 9.35 0.352 0.368 e 2.40 2.70 0.094 0.106 e1 4.95 5.15 0.195 0.203 e 10 10.40 0.394 0.409 l 13 14 0.512 0.551 l1 3.50 3.93 0.138 0.155 l2 1.27 1.40 0.050 0.055 e l2 l1 b1 d a1 c c2 a b e e 1 l
package information stps41h100c 6/9 doc id 8613 rev 5 table 6. to-220ab dimensions ref. dimensions millimeters inches min. max. min. max. a 4.40 4.60 0.173 0.181 c 1.23 1.32 0.048 0.051 d 2.40 2.72 0.094 0.107 e 0.49 0.70 0.019 0.027 f 0.61 0.88 0.024 0.034 f1 1.14 1.70 0.044 0.066 f2 1.14 1.70 0.044 0.066 g 4.95 5.15 0.194 0.202 g1 2.40 2.70 0.094 0.106 h2 10 10.40 0.393 0.409 l2 16.4 typ. 0.645 typ. l4 13 14 0.511 0.551 l5 2.65 2.95 0.104 0.116 l6 15.25 15.75 0.600 0.620 l7 6.20 6.60 0.244 0.259 l9 3.50 3.93 0.137 0.154 m 2.6 typ. 0.102 typ. diam. 3.75 3.85 0.147 0.151 a c d l7 dia l5 l6 l9 l4 f h2 g g1 l2 f2 f1 e m
stps41h100c package information doc id 8613 rev 5 7/9 figure 11. footprint (dimensions in mm) table 7. d 2 pak dimensions ref. dimensions millimeters inches min. max. min. max. a 4.40 4.60 0.173 0.181 a1 2.49 2.69 0.098 0.106 a2 0.03 0.23 0.001 0.009 b 0.70 0.93 0.027 0.037 b2 1.14 1.70 0.045 0.067 c 0.45 0.60 0.017 0.024 c2 1.23 1.36 0.048 0.054 d 8.95 9.35 0.352 0.368 e 10.00 10.40 0.393 0.409 g 4.88 5.28 0.192 0.208 l 15.00 15.85 0.590 0.624 l2 1.27 1.40 0.050 0.055 l3 1.40 1.75 0.055 0.069 m 2.40 3.20 0.094 0.126 r 0.40 typ. 0.016 typ. v2 0 8 0 8 g l l3 l2 b b2 e * flat zone no less than 2m m a c2 d r a2 m v2 c a1 * 16.90 10.30 8.90 3.70 5.08 1.30
ordering information stps41h100c 8/9 doc id 8613 rev 5 3 ordering information 4 revision history table 8. ordering information order code marking package weight base qty delivery mode stps41h100ct stps41h100ct to-220ab 2.20 g 50 tube stps41h100cg stps41h100cg d 2 pak 1.48 g 50 tube stps41h100cg-tr stps41h100cg d 2 pak 1.48 g 1000 tape and reel stps41h100cr stps41h100cr i 2 pak 1.49 g 50 tube table 9. document revision history date revision changes jul-2003 3a previous release. 15-jul-2011 4 updated ta bl e 5 . 11-apr-2012 5 removed order codes stps41h100cr-h and stps41h100ct-h. replaced paragraph under ta bl e 5 .
stps41h100c doc id 8613 rev 5 9/9 please read carefully: information in this document is provided solely in connection with st products. stmicroelectronics nv and its subsidiaries (?st ?) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described he rein at any time, without notice. all st products are sold pursuant to st?s terms and conditions of sale. purchasers are solely responsible for the choice, selection and use of the st products and services described herein, and st as sumes no liability whatsoever relating to the choice, selection or use of the st products and services described herein. no license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. i f any part of this document refers to any third party products or services it shall not be deemed a license grant by st for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoev er of such third party products or services or any intellectual property contained therein. unless otherwise set forth in st?s terms and conditions of sale st disclaims any express or implied warranty with respect to the use and/or sale of st products including without limitation implied warranties of merchantability, fitness for a parti cular purpose (and their equivalents under the laws of any jurisdiction), or infringement of any patent, copyright or other intellectual property right. unless expressly approved in writing by two authorized st representatives, st products are not recommended, authorized or warranted for use in milita ry, air craft, space, life saving, or life sustaining applications, nor in products or systems where failure or malfunction may result in personal injury, death, or severe property or environmental damage. st products which are not specified as "automotive grade" may only be used in automotive applications at user?s own risk. resale of st products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by st for the st product or service described herein and shall not create or extend in any manner whatsoev er, any liability of st. st and the st logo are trademarks or registered trademarks of st in various countries. information in this document supersedes and replaces all information previously supplied. the st logo is a registered trademark of stmicroelectronics. all other names are the property of their respective owners. ? 2012 stmicroelectronics - all rights reserved stmicroelectronics group of companies australia - belgium - brazil - canada - china - czech republic - finland - france - germany - hong kong - india - israel - ital y - japan - malaysia - malta - morocco - philippines - singapore - spain - sweden - switzerland - united kingdom - united states of america www.st.com
|
